Dual Channel Process Universal Indicator
♦ Micro-Controller Based Power, Full & Highly Reliable Controller.
♦ 2 Nos. Universal Input T/C, RTD, Linear Input Selection.
♦ Potential Free Relay Contact Output Up To 1/2/3/4 Nos.
♦ 0.1% Accuracy Of FSD.
♦ Isolated 2 X 0/4-20 mA Process Value Retransmission Output.
♦ All Configurations And Calibration From Front Panel Keypad.
♦ Highly Communicative Serial Interface Facility (RS 232/485).
♦ Transmitter Loop Power Supply With Current Limit As Standard.
♦ Power Supply :230V/110V AC. Or 24V/12V DC.
♦ Optional GSM Mobile Connectivity.
♦ Fully Password Protected Operation.
♦ Transmitter Loop Power Supply With Current Limit As Standard.
♦ µP Based Power, full & highly reliable controller.
♦ 2 nos. Universal Input T/C, RTD, linear input selection.
♦ Potential Free Relay contact output up to 1/2/3/4
♦ 0.1% Accuracy of FSD.
♦ Isolated 2 X 0/4-20mA process value retransmission output.
♦ All Configurations and calibration from front panel keypad.
♦ Highly communicative serial interface facility (RS 232/485).
♦ Transmitter loop power supply with current limit as standard.
♦ Power supply :230V/110V AC. Or 24V/12V DC
♦ Optional GSM mobile connectivity.
♦ Fully Password Protected Operation.
| INPUT | INPUT Type For Channel-1 & Channel-2 | T/C | K, J, R, S, E, N, T |
| RTD | Pt-100, Cu 53 ( 2 wire & 3 wire) | ||
| Current | 0 ~ 20 mA DC, 4~20 mA DC | ||
| Voltage | 0-5V/1-5V DC, 0.5 -2.5V/0- 10 V DC | ||
| Special on demand : | 0-75/200 mV & 0-1/10V/100/300 V AC/DC | ||
| Resistance :- | 0-75/200 mV 0-100/300V DC && 0-500 R , 0-1/5/10 K, 1M | ||
| Transmitter Power Supply | 24 V DC @ 30 mA Max, Isolated From I/P & O/P | ||
| Cold Junction Comp. & Sensor Break Indication | Software Base Automatic | ||
| Range Limits | As Per Input Range Table | ||
| Accuracy | +/- 0.1 % Of Span For Linear & RTD, +/-0.25 % For T/C | ||
| Input Impedance | >330 K For Voltage ,mV DC, And T/C, 100 R For Current | ||
| INDICATION | Indication | PV & SV For UT102 & PV For UT101- LED 4 Digit 7 Segment Display. | |
| Status Indication | LEDs For Relay Status & Communication | ||
| Alarm Modes | Very Low/Low/High/Very High | ||
| CONTROL MODE | On Off Control | Relay / SSR | |
| Dead Band Controls | High And Low Set Point For Level Application | ||
| OUTPUT | Relay Output | NO - C - NC Contacts , 5A@240 V AC Resistive | |
| SSR Output | 1 / 2 / 3 / 4 Relays / SSR Output | ||
| Transmitter Power | 24 V DC @ 20 mA ,12 V DC @ 20 mA | ||
| Retransmission Current & Voltage Outputs | 2 Nos. 0~20/ 4~20 mA DC , 0 ~ 5 V , 0 ~ 1 0 V DC , 1 ~ 5V DC, Fully 3 Port Isolated | ||
| COMMUNICATION | Communication Protocol & Method | Modbus RTU RS- 485/RS- 232 Communication | |
| Programmable Parameter & Max No | Baud Rate, Parity , Node Address , Stop Bit & 0-256 Unit | ||
| Wireless Communication | GSM/GPRS Base Mobile(SMS) Communication | ||
| PROGRAMMABLE PARAMETER | Set point / Hysteresis / High scale / Low Scale | Full Range As Per Input Selection | |
| Relay Logic | F.S. High & Low Alarm, Dead Band Alarm | ||
| Display Resolution | -1999 to 9999 Fully Configurable For Linear Input | ||
| Programming Of Parameters | Through 4 Tactile Keys | ||
| OTHER | Dimensions & Mounting | As Per Box Selection & Wall/Structure 2/2 Holes | |
| (A) Supply Voltage (B) Power Consumption | (A) 110/230 V AC/24 V DC, 50/60 Hz (B) 4 Watts Maximum | ||
| Operating Ambient Temperature And Humidity | 0~50 °C , And Humidity : Below 90%, Non Condensing | ||
