POWER TRANSDUCER
♦ Microprocessor Based Slim & Compact Design ( 22.5 mm Width).
♦ Supplemented With 1,2,3,4 Isolated Outputs For One Input Option.
♦ Universal Inputs Like: AC / DC Volt, AC / DC Current, milliamp, millivolt, RTD, TC & Linear.
♦ 1.5 kV 3 Port Isolation. & 0.25% Accuracy Of FSD.
♦ Design Make As Per Requirements Of IEC Standard & CE Standard.
♦ 24 V DC / 220 V AC / 110 V AC 4 Wire Type Isolation.
♦ All Configurations And Calibration From Front Panel Keypad.
♦ Highly Communicative Serial Interface Facility (RS-232 /485).
♦ Transmitter Loop Power Supply With Current Limit As Standard.
♦ Micro controller based fully isolated design.
♦ Supplemented with 1,2,3,4 isolated outputs for one input option.
♦ AC / DC volt, AC / DC current, milliamp, millivolt, RTD,Thermocouple, Frequency or load cell inputs available.
♦ 1.5 KV 3 Port Isolation. & 0.25% Accuracy of FSD.
♦ Design make as per requirements of IEC Standerds & CE Standerds.
♦ 24VDC/220VAC/110VAC with 4 wire isolation.
♦ All Configurations and Calibration from front panel keypad.
♦ Highly communicative serial interface facility (RS 232 / 485).
♦ Transmitter loop power supply with current limit as standard.
| INPUT | Input Type | Current : | 0-20 mA DC, 4-20 mA DC 0-1/2/5 AMP AC |
| Voltage | DC: 0-75/200 MV DC, 0-1/5/10 VDC, 0-100/300/500 VDC | ||
| AC: 100/200/300/500 AC | |||
| Resistance : | 0-50/500 , 0-1/5/10 K , Hz : 500 HZ,0-1/25Khz | ||
| Transmitter Power Supply | 10/12/24 V DC @ 30 mA Max, Isolated | ||
| Cold Junction Comp. & Sensor Break Ind. | Software Base Automatic | ||
| Response Time | 1 ms to 200 ms Default 200 ms. | ||
| Accuracy | +/- 0.1 % Of Span For Linear & RTD , +/-0.25 % For T/C | ||
| Input Impedance | >330 K For Voltage , mV, and T/C , 100 R For Current | ||
| ISOLATION | 1.5 KV AC Between | Input To Output , Input To Power, Output To Power | |
| Output To Output (In Case Of Multiple Output ) | |||
| COMMUNICATION | Communication Protocol & Connectable Number | Modbus RTU RS- 485 / RS - 232 Communications | |
| Programmable parameter & Connectable Number | Baud Rate , Node, Parity, Node Address, Stop Bit. & 0-256 Unit. | ||
| PROGRAMMBALE PARAMETERS | Programmable Parameter | Through Computer Software | |
| Input / Output Range And Calibrations | Through Computer Software And Local Hardware Trim Pot | ||
| OUTPUT | Output Type | 0-20 mA, 4-20 mA, 0-10 V, 0-2 V, 0-5 V, 0-10 V DC | |
| Nos Off Output | 1/2/3/4 All Are Isolated. | ||
| OTHER | Dimensions & Mounting | As Per Order & Din Rail Mounted | |
| Supply Voltage Power Consumption | 110/230 V AC, 50/60 Hz or 24 V DC 10 Watts Maximum | ||
| Operating Ambient Temperature And Humidity | 0~50 °C Below 90%, Non Condensing | ||
